INCOLOY 020 (UNS N08020) has excellent corrosion resistance in chemical environments containing sulfuric acid and useful resistance in environments containing chloride, nitric acid and phosphoric acid. Other uses include the production of gasoline, solvents, explosives, inorganic and organic chemicals, pharmaceuticals, and food and synthetic materials. INCOLOY 020 is easy to manufacture and is used in the production of mixing tanks, heat exchangers, process piping, pickling equipment, pumps, valves, fasteners and fittings.
Incoloy 330 (N08330) is a nickel-iron-chromium austenitic alloy designed for oxidation and carburizing at high temperatures. The nickel content of 34%-37% gives the material high resistance to chloride stress corrosion cracking and sigma phase precipitation embrittlement. The material is machined through standard machining procedures for stainless steel and nickel alloys. It is widely used to resist corrosion in the environment where circulating heating and carburizing are combined.
Monel 400 (UNS N04400, NCu30) is a high-strength single-phase solid solution alloy. It is a widely used corrosion-resistant alloy with good overall performance. This alloy exhibits excellent corrosion resistance in hydrofluoric acid and fluorine gas environments, as well as in hot concentrated alkaline solutions. Additionally, it is resistant to corrosion from neutral solutions, water, seawater, atmosphere, and organic compounds. An important characteristic of this alloy is that it generally does not produce stress corrosion cracks and has good machinability.
4J29 alloy, also known as Kovar alloy, has a linear expansion coefficient similar to that of silicon-boron hard glass in the temperature range of 20 to 450°C. It has a relatively high Curie point and good low-temperature structural stability. The oxide film of the alloy is dense and can be well wetted by glass. It does not react with mercury, making it suitable for use in instruments that discharge mercury. It is a primary sealing structural material for electronic vacuum devices.
The 4J36 alloy, also known as Invar, has a Curie point of approximately 230°C. Below this temperature, the alloy is ferromagnetic and has a very low coefficient of expansion, while above this temperature, the alloy becomes non-magnetic and the coefficient of expansion increases. This alloy is mainly used to manufacture components that maintain a nearly constant size within a range of temperature variations, and it is widely used in the radio industry, precision instruments, gauges, and other industries.
The 4J32 alloy, also known as Super-Invar, has a lower coefficient of thermal expansion than the 4J36 alloy in the temperature range of -60 to 80°C, but its low-temperature structural stability is inferior to that of the 4J36 alloy. This alloy is mainly used for manufacturing highly precise instrument parts that require dimensional stability within a range of environmental temperature changes.
4J33 is a ceramic sealing alloy developed based on the characteristics of ceramics in our country. The alloy has a linear expansion coefficient similar to that of 95% Al2O3 ceramics within the temperature range of -60℃ to 600℃. It is mainly used for matching seals with ceramics and is an important sealing structural material in the vacuum electronics industry.
4J34 is a ceramic sealing alloy developed based on the characteristics of ceramics in our country. The alloy has a linear expansion coefficient similar to that of 95% Al2O3 ceramics within the temperature range of -60℃ to 600℃. It is mainly used for matching seals with ceramics and is an important sealing structural material in the vacuum electronics industry.
NS111 (N08825, 2.4858 alloy) has the following characteristics: (1) Good resistance to stress corrosion cracking. (2) Good resistance to pitting and crevice corrosion. (3) Excellent oxidation resistance and non-oxidizing acidic performance. (4) Very good mechanical properties at room temperature and at high temperatures up to 550°C. (5) Certified for manufacturing pressure vessels at temperatures up to 450°C.
NS334 (Hastelloy C-276, N06645) alloy is a nickel-chromium-molybdenum alloy containing tungsten, with very low silicon and carbon content. It is an improved version of NS333. Compared to NS333, NS334 has a carbon content that is 0.06% lower, making it an ultra-low carbon alloy steel. It has better corrosion resistance than NS333 alloy steel, reduced susceptibility to intergranular corrosion, and increased resistance to pitting corrosion.
NS112 (N08811, 1.4876) is a fully austenitic low-carbon nickel-iron-chromium alloy that belongs to the same series as Incoloy 800, with cobalt content strictly controlled to below 0.01%. NS112 is resistant to many corrosive media. Its high nickel content provides excellent resistance to stress corrosion cracking under aqueous corrosion conditions. The high chromium content enhances its resistance to pitting and crevice corrosion cracking. This alloy exhibits good resistance to nitric acid and organic acid corrosion, but its corrosion resistance in sulfuric acid and hydrochloric acid is limited. Aside from potential pitting corrosion in halides, it shows good corrosion resistance in both oxidizing and non-oxidizing salts. It also demonstrates excellent corrosion resistance in water, steam, and mixtures of steam, air, and carbon dioxide. Applications include nitric acid condensers—resistant to nitric acid corrosion, steam heating tubes—exhibiting good mechanical properties, and heating element tubes—also with good mechanical properties. For applications in environments up to 500°C, the alloy is in an annealed state.
During the heat treatment process, it is important to avoid contact with sulfur, phosphorus, lead, and other low-melting-point metals, as this can make the Nicrofer 6616 hMo alloy brittle. Care should be taken to remove contaminants such as marking paint, temperature indicating paint, colored crayons, lubricating oil, and fuel. The lower the sulfur content in the fuel, the better; the sulfur content in natural gas should be less than 0.1%, and in heavy oil, it should be less than 0.5%. Electric furnace heating is a better choice because it allows for precise temperature control and clean furnace gas. If the gas furnace has sufficiently pure gas, it can also be selected.
NS335 (Hastelloy C-4, N06645, 2.4610) alloy is an austenitic low-carbon nickel-molybdenum-chromium alloy. The main difference between it and Nicrofer 6616 hMo and other similarly developed alloys with similar chemical compositions is the lower content of carbon, silicon, iron, and tungsten. This chemical composition provides excellent stability at temperatures ranging from 650 to 1040°C, enhances resistance to intergranular corrosion, and can avoid edge line corrosion sensitivity and corrosion in the heat-affected zone of welds under appropriate manufacturing conditions.
Hastelloy C-4 (N06455) is an austenitic low-carbon nickel-molybdenum-chromium alloy. The main difference between it and similar alloys with earlier developed chemical compositions, such as Nicrofer 6616hMo, is the lower content of carbon, silicon, iron, and tungsten. This chemical composition provides excellent stability at temperatures ranging from 650 to 1040°C, enhances resistance to intergranular corrosion, and can avoid edge line corrosion sensitivity and corrosion in the heat-affected zone of welds under appropriate manufacturing conditions.
Hastelloy C-2000 (N06200, 2.4675) is a nickel-based superalloy composed of elements such as nickel, molybdenum, and chromium, with a nickel content of about 55%. Hastelloy C-2000 was developed as an optimized alloy to expand the range of applications for materials, starting from a conceptual idea of adding copper to the already well-established Ni-Cr-Mo alloys. Since its market introduction at the end of 1995, it has received significant recognition due to its inherent versatility. Technological innovations have not only improved the alloy's resistance to aqueous corrosion but also expanded the overall application range of the Ni-Cr-Mo family of alloys.