Product classification
GH4145 nickel-based deformed high-temperature alloy
The GH4145 (GH145) alloy is a nickel-based superalloy that is strengthened by aging with the γ′ [Ni3(Al, Ti, Nb)] phase. It exhibits good corrosion resistance and oxidation resistance below 980°C, high strength below 800°C, and good relaxation resistance below 540°C. Additionally, it has excellent formability and weldability. This alloy is primarily used to manufacture ring parts, structural components, and bolts that operate below 800°C and require high strength and corrosion resistance, as well as flat springs and helical springs that operate below 540°C with moderate or lower stress and require relaxation resistance. It can also be used to manufacture parts such as gas turbine blades. Available forms include plates, strips, bars, forgings, rings, wires, and tubes.
Classification:
Key words:
Superalloy | Inkenel | Hastelloy | Inkloy | Precision Alloy Series
Product Parameters
GH4145
GH4145 nickel-based deformed high-temperature alloy
Chinese grade: GH145/GH4145
American grade: Inconel X-750
German grade: NiCr15Fe7TiAl
1.Overview of GH4145(GH145) high-temperature alloy:
GH4145(GH145) alloy is mainly a nickel-based high-temperature alloy that is strengthened by aging with the γ′[Ni3(Al, Ti, Nb)] phase. It has good corrosion resistance and oxidation resistance below 980℃, high strength below 800℃, and good relaxation resistance below 540℃. It also has good formability and weldability. This alloy is mainly used to manufacture ring parts, structural parts, and bolts that work below 800℃ and require high strength and corrosion resistance, as well as flat springs and helical springs that work below 540℃ with medium or lower stress and require relaxation resistance. It can also be used to manufacture parts such as gas turbine blades. Available forms include plates, strips, bars, forgings, ring parts, wires, and pipes.
1. GH4145(GH145) high-temperature alloy material grade: GH145(GH4145)
2. GH4145(GH145) high-temperature alloy similar grades: Inconel X-750 (USA), NiCr15Fe7TiAl (Germany).
3. Technical standards for GH4145(GH145) high-temperature alloy material:
4. Chemical composition of GH4145(GH145) high-temperature alloy: see Table-1.
Table-1
| C≤ | Si≤ | Mn≤ | P≤ | S≤ | Cr≥ | Ni+Co≥ | Mo≥ | Cu≤ |
| 0.08 | 0.50 | 1.00 | 0.015 | 0.010 | 14.0-17.0 | 70.0 | 0.50 | |
| Others | Co≤ | Al≤ | Ti≤ | Fe≤ | B≤ | Ce≤ | W≤ | Nb+Ta |
| 1.00 | 0.40-1.00 | 2.25-2.75 | 5.0-9.0 | 0.70-1.20 |
Note: The Mn and Si in the table are the contents for bars, forgings, ring parts, and wires. For plates, strips, and pipes: ω(Mn)≤0.35%, ω(Si)≤0.35%.
5. Heat treatment system for GH4145(GH145) high-temperature alloy: The solution heat treatment system for plates, strips, and pipes is 980℃±15℃, air-cooled. The intermediate heat treatment system for materials and parts can choose the following processes for heat treatment.
(1) Annealing: 955~1010℃, water-cooled.
(2) Annealing before welding for welded parts: 980℃, 1h.
(3) Stress relief annealing for welded parts: 900℃, hold for 2h.
Stress relief annealing: 885℃±15℃, 24h, air-cooled.
6. Specifications and supply status of GH4145(GH145) high-temperature alloy: Various specifications of bars, forgings, ring parts, hot-rolled plates, cold-rolled plates, strips, pipes, and wires can be supplied. Plates and strips are generally supplied after hot-rolling or cold-rolling, annealing or solution treatment, and acid pickling and polishing. Bars, forgings, and ring parts can be supplied in forged or hot-rolled state; they can also be supplied after solution treatment post-forging; bars can be supplied polished or turned after solution treatment, and can be supplied in cold-drawn state upon order requirements. Pipes are supplied after solution treatment and removal of oxide scale. Wires can be supplied in solution state; for wires with a nominal diameter or thickness below 6.35mm, they can be supplied after solution treatment with 50%~65% cold-drawn deformation; for wires with a nominal diameter or edge length greater than 6.35mm, they are supplied with not less than 30% cold-drawn deformation after solution treatment. For wires with a nominal diameter or edge length not greater than 0.65mm, they are supplied with not less than 15% cold-drawn deformation after solution treatment as required.
7. Melting and casting process of GH4145(GH145) high-temperature alloy: The alloy is melted using electric arc furnace with vacuum consumable remelting, vacuum induction plus electroslag, electroslag plus vacuum consumable remelting, or vacuum induction plus vacuum consumable remelting.
8. Overview and special requirements of GH4145(GH145) high-temperature alloy applications: This alloy is mainly used to manufacture corrosion-resistant flat wave springs, circumferential helical springs, helical compression springs, spring retaining rings, and sealing rings for aircraft engines operating at temperatures below 540℃.
2.Physical and chemical properties of GH4145(GH145) high-temperature alloy:
1. Thermal properties of GH4145(GH145) high-temperature alloy:
(1) Melting temperature range of GH4145(GH145) high-temperature alloy: 1395~1425℃.
(2) Thermal conductivity of GH4145(GH145) high-temperature alloy: see Table 2-1.
Table 2-1[1]
| θ/℃ | 50 | 100 | 300 | 500 | 900 |
| λ/(W/(m·℃)) | 14.7 | 15.9 | 20.1 | 25.1 | 37.3 |
(3) Linear expansion coefficient of GH4145(GH145) high-temperature alloy: see Table 2-2.
Table 2-2[2]
| θ/℃ | 20~200 | 20~300 | 20~400 | 20~500 | 20~600 | 20~700 | 20~800 |
| α/10-6℃-1 | 13.1 | 13.5 | 14.1 | 14.4 | 15.0 | 15.6 | 16.2 |
2. GH4145(GH145) high-temperature alloy density: ρ=8.25g/cm3[7].
3. GH4145(GH145) high-temperature alloy electrical properties: resistivity ρ=1.22×10-6Ω.m at 50℃[6].
Three,GH4145(GH145) high-temperature alloy mechanical properties:
1. The mechanical properties at room temperature for strips, plates, and pipes specified in the technical standards for GH4145(GH145) alloy: see Table 3-1.
Table 3-1
| Variety | Specification δ/mm | Heat treatment system | σb/MPa | σP0.2/MPa | δ4D/% | HRC |
| Strip | Delivery state | ≤930 | - | ≥18 | - | |
| Delivery state +730℃±10℃, 8h, furnace cooling 55℃/h or air cooling to 620℃±10℃, 8h, air cooling, total aging time not less than 18h | ≥1105 | - | ≥12 | ≥30 | ||
| Plate | ≤0.60 | Delivery state | ≤930 | ≤515 | ≥30 | - |
| >0.60 | ≤930 | ≤515 | ≥35 | - | ||
| Plate | Delivery state +730℃±10℃, 8h, furnace cooling 55℃/h or air cooling to 620℃±10℃, 8h, air cooling, total aging time not less than 18h | ≥1170 | ≥795 | ≥18 | ≥32 | |
| Pipe | Delivery state | ≤965 | ≤550 | ≥35 | - | |
| Delivery state +730℃±10℃, 8h, furnace cooling 55℃/h or air cooling to 620℃±10℃, 8h, air cooling, total aging time not less than 18h | ≥1170 | ≥790 | ≥15 | - |
Note: The delivery state is solution treatment at 980℃±15℃, holding for an appropriate time, air cooling or rapid cooling, and removing the oxide scale.
2. The mechanical properties at room temperature for wires specified in the technical standards for GH4145(GH145) alloy: see Table 3-2.
Table 3-2
| Variety | Specification/mm | Heat treatment system | Round wire | Square or flat wire |
| σb/MPa | σb/MPa | |||
| Wire | ≤6.35 | Class A, delivery state | ≥1310 | ≥1210 |
| >6.35~15.88 | ≥1110 | ≥1110 | ||
| ≤0.65 | Class B, delivery state | ≤1030 | ||
| >0.65~12.70 | 895~1140 | |||
| ≥0.30~6.35 | Class A, delivery state +650℃±10℃, 4h, air cooling | ≥1520 | ||
| >6.35~10.60 | ≥1380 | |||
| >10.60~15.90 | ≥1240 | |||
| ≥0.30~6.35 | Class A, delivery state +1150℃±10℃, 2h, air cooling, +840℃±10℃, 24h, air cooling, +650℃±10℃, 20h, air cooling | ≥1030 | ||
| >6.35~15.90 | ≥1000 | |||
| ≤0.65 | Class B +730℃±10℃, 16h, air cooling | ≥1070 | ||
| >0.65~12.70 | ≥1140 |
Note: In the delivery state, the wire is solution treated at a certain temperature within 1090~1200℃ before cold drawing to finished product, and then cold drawn according to the following specifications;
Class A: For wire with nominal diameter or edge length not exceeding 6.35mm, the cold drawing deformation amount is 50%~65%; for wire with nominal diameter or edge length greater than 6.35mm, the cold drawing deformation amount is more than 30%.
Class B: For wire with nominal diameter or edge length not exceeding 0.65mm, the cold drawing deformation amount is about 15%.
3. The durability performance specified for GH4145(GH145) alloy bars, forgings, and rings: see Table 3-3.
Table 3-3[3]
| θ/℃ | σ/MPa | t/h | δ4D/% |
| 730℃±3℃ | 362 | ≥23 | ≥5 |
Four,GH4145(GH145) high-temperature alloy microstructure:
1. GH4145(GH145) high-temperature alloy phase transformation temperature: The γ′ phase begins to precipitate at about 600℃, with a peak precipitation at about 800℃, starts to dissolve at 900℃, and is almost completely dissolved at 970℃.
2. GH4145(GH145) high-temperature alloy time-temperature-structure transformation curve:
3. GH4145(GH145) high-temperature alloy microstructure: After standard heat treatment, the microstructure consists of a γ matrix, Ti(C, N), Nb(C, N), M23C6 carbides, and γ′[Ni3(Al, Ti, Nb)] phase, with γ′ content approximately 14.5%, which is the main strengthening phase of the alloy.
Five,GH4145(GH145) high-temperature alloy process performance and requirements:
1. GH4145(GH145) high-temperature alloy forming performance: The forging temperature of the alloy is easily formable between 1220~950℃. The heating temperature for forging the steel ingot can be at 1200℃. To ensure that the final forged parts or bars achieve good microstructure and performance, subsequent forging heating should be conducted at relatively lower temperatures. The final forging temperature should not be lower than 950℃. This alloy should undergo solution treatment after severe forming processes.
2. GH4145(GH145) high-temperature alloy welding performance: The alloy has good welding performance and can be welded in various ways, but it is difficult to perform fusion welding on large cross-section parts, while small cross-section parts and thin plates have better welding performance. Welding must be performed after annealing or solution treatment, and post-welding stress relief treatment should be conducted at 980℃ for 0.5h or 900℃ for 2h. The welded assembly should then undergo aging treatment to achieve strength close to that of a fully heat-treated state.
3. GH4145(GH145) high-temperature alloy parts heat treatment process: The heat treatment of parts should be conducted in a sulfur-free neutral or reducing atmosphere to avoid sulfidation. Parts should avoid "hot-cold" treatment between 870~650℃. For large cross-section parts, to prevent cracking, they should be air-cooled after solution treatment. The final heat treatment for finished parts:
(1) For components working above 600℃, requiring optimal long-term creep performance:
a. Solution: 1150℃±15℃, hold for 2~4h, air cool;
b. Aging: 845℃±15℃, hold for 24h, air cool + 705℃±15℃, hold for 24h, air cool.
(2) For components working below 600℃, requiring optimal room temperature and high-temperature tensile performance:
a. Solution: 980℃±15℃, hold for 1h, air cool;
b. Aging: 730℃±15℃, hold for 8h, cool to 620℃±10℃ at 50℃/h, hold for 8h, air cool.
(3) Ring parts generally adopt the following heat treatment system:
a. Solution: 1095℃±15℃, hold for 2-4h, air cool;
b. Aging: 845℃±15℃, hold for 24h, air or furnace cool to +705℃±15℃, hold for 20h, air cool.
(4) For bars and forgings used at temperatures below 600℃, the following heat treatment system is adopted:
a. Homogenization: 885℃±15℃, hold for 24h, air cool;
b. Aging: 705℃±15℃, hold for 20±1h, air cool.
(5) Annealed plates and strips, as well as plates and wires used for springs, can be treated with the following system:
a. Solution: 980℃±15℃, hold for 1h, air cool;
b. Aging: 1) 705℃±15℃, hold for 22h, air cool;
(6) 760℃±10℃, hold for 1h, air cool.
a. Solution: 980℃±15℃, hold for 1h, air cool;
b. Aging: 730℃±10℃, hold for 8h, cool to +620℃±10℃ at 50℃/h, hold for 8h, air cool.
4. GH4145(GH145) high-temperature alloy surface treatment process:
GH4145(GH145) alloy cutting and grinding performance: The alloy can be machined in various states, with good machining performance in annealed or solution-treated states.
Six,GH4145(GH145) high-temperature alloy varieties, specifications, and supply status:
1. Variety classification: GH4145 seamless pipes, GH4145 steel plates, GH4145 round steel, GH4145 forgings, GH4145 flanges, GH4145 rings, GH4145 welded pipes, GH4145 steel strips, GH4145 wires, and matching GH4145 welding materials.
2. Delivery status: Seamless pipes: solution + acid pickling, length can be specified; plates: solution, acid washing, edge cutting; welded pipes: solution acid pickling + RT% flaw detection, forgings: annealed + turned; bars in forged-rolled state, surface polished or turned; strips delivered in cold-rolled, solution soft state, and descaled; wires delivered in solution acid-washed coil or straight bar form, solution straight bar fine polished state.
Previous Page
Next Page
Previous Page
GH1015 iron-based high-temperature alloy
Next Page
Related Products
Product Consulting
Leave your contact information to get a free product quote!