Product classification
GH30
Overview of GH30 The alloy is a single-phase austenite after solution treatment, and its structure remains stable during use. The main products are cold-rolled thin plates, but it can also supply deformed products such as bars, rings, wires, and tubes. The products are primarily used for components of turbine engine combustion chambers operating below 800°C and other high-temperature components that require oxidation resistance but bear very little load below 1100°C.
Classification:
Key words:
Superalloy | Inkenel | Hastelloy | Inkloy | Precision Alloy Series
Product Parameters
Overview of GH30
The alloy is a single-phase austenite after solid solution treatment, and its structure is stable during use. The main products are cold-rolled thin plates, but it can also supply deformed products such as bars, rings, wires, and pipes. It is primarily used for turbine engine combustion chamber components working below 800℃ and other high-temperature components that require oxidation resistance but bear very little load below 1100℃.
1.1 Material Grade
GH30 (GH3030)
1.3 Technical Standards of the Material
GJB 1952-1994 "Specification for Cold-Rolled Thin Plates of High-Temperature Alloys for Aviation"
GJB 2297-1995 "Specification for Cold-Drawn (Rolled) Seamless Tubes of High-Temperature Alloys for Aviation"
GJB 2611-1996 "Specification for Cold-Drawn Bars of High-Temperature Alloys for Aviation"
GJB 2612-1996 "Specification for Cold-Drawn Wires of High-Temperature Alloys for Aviation"
GJB 3020-1997 "Specification for Ring Blanks of High-Temperature Alloys for Aviation"
GJB 3317-1998 "Specification for Hot-Rolled Plates of High-Temperature Alloys for Aviation"
GJB 3318-1998 "Specification for Cold-Rolled Strips of High-Temperature Alloys for Aviation"
GJB 3165-1998 "Specification for Hot-Rolled and Forged Bars of High-Temperature Alloys for Aviation"
GJB 3167-1998 "Specification for Cold-Drawn Wires of High-Temperature Alloys for Cold Heading"
GB/T 15062-1994 "General High-Temperature Alloy Tubes"
1.4 Chemical Composition
Table 1-1
|
C |
Cr |
Ni |
Ti |
Al |
Fe |
Mn |
Si |
P |
S |
|
≤0.12 |
19.0~22.0 |
Remainder |
0.15~0.35 |
≤0.15 |
≤1.5 |
≤0.7 |
≤0.8 |
≤0.03 |
≤0.02 |
Note: 1. For bars and ring blanks, the standard specifies Cu≤0.20%.
2. For hot-rolled plates, cold-rolled plates, cold-rolled strips, tubes, wires, and cold heading cold-drawn wires, the standard specifies Fe≤1.00%, P≤0.015%, S≤0.010%, Pb≤0.001%, Cu≤0.007%.
1.5 Heat Treatment System
The cooling method for hot-rolled plates, cold-rolled thin plates, and ring blanks is air cooling; for cold heading wires and cold-drawn bars, it is water cooling or air cooling; for tubes, it is water cooling.
1.6 Variety Specifications and Supply Status
Various specifications of deformed products can be produced, with bars and ring blanks delivered without heat treatment; hot-rolled plates and cold-rolled thin plates and tubes are supplied after solid solution and acid pickling; welding wires are delivered in cold-drawn state, solid solution and acid pickling state, or semi-hard state in coils; cold heading wires are delivered in solid solution, acid pickling state in coils or straight bars, solid solution straight bars polished or cold drawn; tubes are delivered in solid solution, acid pickling state; cold-drawn bars are delivered in annealed, annealed plus acid pickling, annealed plus polished, or cold drawn state.
1.7 Melting and Casting Process
Electric arc furnace melting or electric arc furnace melting plus electroslag remelting or vacuum arc remelting, non-vacuum induction furnace plus electroslag melting or vacuum arc furnace remelting or vacuum double process.
1.8 Application Overview and Special Requirements
This alloy has undergone long-term testing in aviation engines, mainly used for combustion chamber and afterburner components as well as casing installation edges.
Previous Page
Next Page
Previous Page
GH4043/GH43 high-temperature alloy
Next Page
Related Products
Product Consulting
Leave your contact information to get a free product quote!